指针推进移动性管理策略中指针链长度的概率

为了降低移动通信网络中位置跟踪操作的代价,指针推进策略被提出.显然,指针链长度的确定对这一策略的有效应用是至为重要的.已有论文假定移动台在位置区的逗留时间服从指数分布的条件下,对指针链的长度进行研究,但指数分布的特殊性,限制了其研究结果的应用.本文推广了上述结果,研究了移动台在位置区的逗留时间服从一般概率分布的指针推进策略,通过构造向量马氏过程,利用密度演化方法,导出了指针链长度的概率公式,这个公式可用于对各种指针推进策略性能的评价.     

固井声幅-变密度测井的影响因素分析

利用声幅－变密度测井进行固井质量的评价受到诸多因素的影响，各种影响因素对声幅－变密度测井资料的影响作用有较大的差异，根据大量测井资料分析和实验研究，对仪器偏心、测井时间，套管尺寸与重量，地层岩性，气侵、水泥环微间隔等因素的影响作用进行了较为深入的分析，为各种影响因素的识别与校正提出了相应的方法和依据。     

高密度低损害压井液体系

为了解决修井、射孔等作业过程中压井液的漏失、滤失问题,以及由此造成的水敏、水锁、固相堵塞、乳液堵塞等地层损害,提出并研制了一种含可溶性固相的暂堵型高密度压井液配方体系。该体系主要由XC聚合物和YDC-LN助剂以及可水溶性加重剂组成。通过配方筛选和室内模拟试验研究,结果表明该体系稳定性好,耐温超过105℃,滤失量小,抑制性强,岩心损害率小于20%,而且具有密度可调、返排率高等特点;与自来水和油田污水的配伍性好,应用简单、方便。     

Modeling of Energy Density Distribution in Rock Mass on the Basis of Seismotectonic and Geodetic Data

Using the focal mechanisms of earthquakes taken place from 1950 to 1996, the type and direction of principal strains were established, which made it possible to determine the volume stress-strain state of the south-east flank of the Baikal rift zone on the basis of the inverse problem solution. The variations in the stress-strain fields and spatial distribution of the stored potential energy density were found by the displacements of the daylight surface points in Tunkinsk geodetic proving ground in 1975 - 1986.     

控制图在土坝粘土填筑干密度控制中的应用

应用统计控制图法，选用平均值——标准差、平均值——极差控制图法，控制24^#坝粘土填筑干密度值及施工偶然异常波动，早期提出警报，以保证土坝的施工质量。     

钻探用变量泥浆泵曲轴强度的计算

随着钻探业的不断发展 ,日趋需要大功率的泥浆泵 ,文章介绍了大变量泥浆泵机组中曲轴的设计。     

Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

Low density polyethylene and grafted lignin polyblends using epoxy‐functionalized compatibilizer: mechanical and thermal properties

Lignin was graft copolymerized with methyl methacrylate using manganic pyrophosphate as initiator. This modified lignin was then blended (up to 50 wt%) with low density polyethylene (LDPE) using a small quantity of poly[ethylene‐co‐(glycidyl methacrylate)] (PEGMA) compatibilizer. The mechanical properties of the blend were substantially improved by using modified lignin in contrast to untreated lignin. Differential scanning calorimetry studies showed loss of crystallinity of the LDPE phase owing to the interaction between the blend components. Thermogravimetric analysis showed higher thermal stability of modified lignin in the domain of blend processing. This suggested that there is scope for useful utilization of lignin, which could also lead to the development of eco‐friendly products. Copyright © 2005 Society of Chemical Industry     

Finite‐Element Implementation of a Self‐consistent Texture Model with a Hardening Law Based on Dislocation Densities

A self‐consistent texture model is implemented in the finite‐element code ABAQUS/Explicit®. Hardening of the slip systems is described by evolution laws for dislocation densities, and the Bauschinger effect is included. With these ingredients the cold rolling of an IF‐steel is simulated and the evolution of texture and anisotropy is examined. The use of the dislocation based hardening law is found to have a significant effect on the evolution of the anisotropic yield surface, but only very little influence on the texture. Furthermore, the hardening model is used to investigate the evolution of dislocation densities in differently oriented grains during plane strain compression. It is found that the dislocation density varies greatly depending on orientation, an observation which can help to explain the orientation dependence of recrystallization.     

Preparation of ultra‐low‐density microcellular materials

Microcellular polymeric materials can be obtained by the polymerization of a high‐internal‐phase emulsion. These materials are good candidates as targets toward inertial confinement fusion. This application requires severe specifications, including a very low density and a small cell size. In this study, we examined the influence of parameters such as emulsification conditions, surfactant nature, and the presence of a porogen on the obtainment of those requirements. It was possible to obtain microcellular polymeric foams with apparent densities as low as 0.0126 g/cm³. However, it was difficult to obtain very low material density and still maintain a small average pore size. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2053–2063, 2005